Crestron control systems can put a friendly face on any complete integrated AV or automation solution. To support the myriad touchpanels, keypads, and other peripherals that make up a control system, the C2NSPWS300 provides a convenient and compact centralized power and termination solution

• 300 Watt regulated power supply
• 8 independently managed outputs
• 16 Cresnet distribution ports

Load Ratings
 

Per Channel
75 Watts (3.125 Amps) @ 24 Volts DC regulated
 
System Total
300 Watts (12.5 Amps) @ 24 Volts DC regulated
 
Ripple / Noise
<150 mV
 
Load Protection
Electronic circuit breaker per channel, each rated at 75 watts nominal / 100 watts maximum; 4 Amp, 125V internal fuse; all channels shut off in case of total system overload
 
Sequential Startup
Outputs activate sequentially when power supply system is enabled (see PWR ON, PWR OFF/SLAVE control)


Power Requirements
4 Amps, 100-240 Volts AC, 50/60 Hz


Connections
 

1 – 8
(16) 4-pin 5mm detachable terminal blocks comprising (2) paralleled Cresnet ports per each of (8) output channels;
24 Volt DC power outputs with Cresnet data pass-thru from NET port
 
NET
(1) 4-pin 5mm detachable terminal block;
Ordinarily connects to the Master Cresnet port of a control system;
Cresnet data ‘Y’ and ‘Z’ terminals pass through to ports 1 – 8;
Applying 24 Volts DC to the ‘24’ and ‘G’ terminals enables the power supply system when in “SLAVE” mode
 
AC Line
(1) attached input power cable (~1 ft long) with inline IEC320 socket;
Connects to grounded AC power source using 3-prong power cable or pigtail cable, both provided


Controls
 

PWR ON, PWR OFF/SLAVE
(1) rocker switch; enables/disables the power supply system if no external DC voltage is applied to the NET port, or selects “SLAVE” mode to allow enabling the power supply system remotely by applying an external 24V DC signal to the NET port
 
RESET 1 – 8
(8) miniature pushbuttons; each resets its respective output channel, or momentarily disables the channel while held
 
SYSTEM RESET
(1) miniature pushbutton; resets all output channels sequentially, or momentarily disables all channels while held
 
SETUP
(1) miniature pushbutton; used for touch-settable ID (TSID)


LED Indicators
 

PWR 1 – 8
(green) Indicate 24V DC power present at each channel output
 
OVRLD 1 – 8
(red) Indicate a load in excess of 75 watts on a given channel, channel output disabled
 
SYSTEM OVRLD
(red) Indicates a total load in excess of 300 watts on the power supply system, all channels disabled
 
PWR
(green) Indicates power supply system is enabled
 
NET
(yellow) Indicates communication with Cresnet system
 
SETUP
(red) Used for touch-settable ID (TSID)


Environmental
 

Temperature
41 Degrees  to 104 Degrees F (5 Degrees  to 40 Degrees C)
 
Humidity
10% to 90% RH (non-condensing)


Enclosure
 

Chassis
Aluminum, black anodized with polycarbonate label overlay, convection-cooled, vented top and sides
 
Mounting
Surface mount using (2) integral mounting flanges, or 3U 19-inch rack-mountable (C2N-RMAK rack kit sold separately)
 
CAEN Automation Enclosure
Occupies 1 module space in a single-width enclosure, or 2 side-by-side module spaces in a double-width enclosure (CAEN-MK mounting kit sold separately)


Dimensions

 
Height
5.19 in (13.18 cm)
 
Width
13.25 in (33.66 cm)
 
Depth
3.29 in (8.36 cm)

Weight
 5.3 lb (2.4 kg)